Rami
Professional audio solutions
Rami proposes a complete range of analog and digital products.
The Rami products are devoloped for the broadcast and industrial environnements.
RAMI also offers a technical support for the installation , a business team to guide you in your project as well as an engineering team which realises your needs.
AMC120
Headphone amplifier, desktop model, external PSU
Headphone amplifier, desktop model, external PSU
AMC 120 is a device used a signal monitoring and red/green light control.
This is in slot unit features a high performance amplifier for two low impedance headphones, with volume control.
* One headphone output with volume on front panel.
* Two 1/4" headphone connectors.
* One "ON" light.
* One signal input, using female Sub-D 15.
AMC230
Ecoute amplifi
Ecoute amplifi
AMC 230 is a two channel local reception amplifier (2 unit 19" rack), owning an analog audio input.
* Volume level and balance control via VCA
* Phasemeter on led bargraph for a complete monitoring of the modulation.
* Leds peakmeter (dBu).
* Headphone output in front panel (6.35mm jack). Automatic switching of internal speakers.
* Mute order via remote control.
* Analog balanced inputs available on the front and rear panel.
* Female DB9 remote control connector (volume and mute).
* Volume control either via front panel switching or via external potentiometer.
AMC250
Ecoute locale A et D
Ecoute locale A et D
AMC 250 is a local reception amplifier unit to fit a 2 unit 19" rack, owning an analog audio input and a digital audio input. This digital audio input accepts all standards (AES/EBU, S/PDIF, IEC 958) up to a 24 bits resolution and a 96 KHz maxi sampling rate.
AMC502
Headphone amplifier VCA, select 1 out of 4, L/R separately.
Headphone amplifier VCA, select 1 out of 4, L/R separately.
The AMC 502 includes a switchable 4 to 1 matrix, a VCA controlled headphone amplifier and a double order Input channel.
AMC502_E
Breakout box for connection between AMC502 and AMC502R
Breakout box for connection between AMC502 and AMC502R
MONITORING & HEADPHONE AMPLIFIERS: Easy wiring box for AMC502 to AMC502R.
AMC502_R
Remote for AMC502
Remote for AMC502
MONITORING & HEADPHONE AMPLIFIERS: Remote control for AMC502.
AMC610
6 separate headphone amplifiers (can be linked) - command input - 1U - 19 inch
6 separate headphone amplifiers (can be linked) - command input - 1U - 19 inch
The AMC 610 is a six headphone distribution amplifier rack unit. This unit allows you to feed six headphones from one or more stereo modulation line inputs (Impedance should be from 8 Ohms to 600 Ohms).
AMC616
Volume control headphone VCA and remote 6,35 jack output for AMC620
Volume control headphone VCA and remote 6,35 jack output for AMC620
VCA Volume headphone control and jack output 6.35 for AMC620
AMC620
Headphone amplifier 6 channel, VCA control - 2 PGM - 2 commands on L, R or L&R
Headphone amplifier 6 channel, VCA control - 2 PGM - 2 commands on L, R or L&R
6 phones vhith VCA 2 order 2 pgm
ASM120 D
Auto mute, Studio RED/GREEN
Auto mute, Studio RED/GREEN
The ASM 120S combines the functions of the Red/Green On Air switch with those of the Automatic Studio Monitor Mute. It directly controls the RGL 260 (2 luminous Red/Green indicators) and the RGL 500 (Red "On Air" visual display) interfaces to indicate the On Air/Off Air function and RGL 700.
AUF200S_EE
Autofader 2 stereo channels broadcast - I/O electronically balanced
Autofader 2 stereo channels broadcast - I/O electronically balanced
The AUF 200S ( 2 channels) and the AUF 300 (3 channels) are automatic mixers / autofaders. All input channels are stereophonic balanced mixed toward a balanced output. The transition from one channel to another is performed by an electronic mixing (fade in/out), which all parameters can be modified. It can be done either by the presence of modulation, or by closing an outside loop, or with a combination of both.
AUF227_EE
Autofader 2 stereo channels broadcast - E/O electronically balanced - 27Hz decoding
Autofader 2 stereo channels broadcast - E/O electronically balanced - 27Hz decoding
The AUF 227 is a two channel automatic mixer / fader. All input channels (A - B) are stereophonic balanced mixed towards a stereophonic balanced output. The transition from one channel to another is performed by an electronic mixing (fade in/out), which all parameters can be modified. This can be done either with the presence of the modulation on channel B, or when detecting a 27 Hz pulse in the channel B modulation, or using a combination of both. Switching using an external loop is also possible.
AUF300_EE
Autofader 3 stereo channels broadcast - I/O electronically balanced
Autofader 3 stereo channels broadcast - I/O electronically balanced
The AUF 200S ( 2 channels) and the AUF 300 (3 channels) are automatic mixers / autofaders. All input channels are stereophonic balanced mixed toward a balanced output. The transition from one channel to another is performed by an electronic mixing (fade in/out), which all parameters can be modified. It can be done either by the presence of modulation, or by closing an outside loop, or with a combination of both.
AUF500
Autofader 2 channels digital broadcast - I/O electronically balanced
Autofader 2 channels digital broadcast - I/O electronically balanced
The AUF 500 is the digital version of the AUF 200S. The mixing procedure and automatic fading is completely digital whilst switching from one source to another. Channel A Input is therefore digital AES/EBU, whilst the Channel B Input is either digital or analogue depending on the option in question.
BAT404
Dedicated control interface on RJ45
Dedicated control interface on RJ45
Control interface - RJ45 - For DHD mixer
BYP200
Bypass option AUF200/300 (Power failure): Select input A, B or C
Bypass option AUF200/300 (Power failure): Select input A, B or C
optional bypass for AUF200 / AUF300
CARTRIDGE
Control desk Cart machine
Control desk Cart machine
The "Cartridge" is a control tool designed to help user controlling radio broadcast softwares easily and efficiently.
CBB404
Impedance convertor AES (double) - BNC -> XLR + XLR -> BNC
Impedance convertor AES (double) - BNC -> XLR + XLR -> BNC
CBB404 allows to convert impedance and format between AES3 balanced 110 Ohms and AESid unbalanced 75 Ohms
CBB404 is a double impedance converter AES3id BNC (75 Ohms) to AES3 XLR (110 Ohms) and a double impedance converter AES3 XLR (110 Ohms) to AES3id BNC (75 Ohms)
This device allows to link digital audio equipments using different formats.
It also allows, when using limited distance AES3 XLR (110 ohms), to move too 75 ohms, the signal travelling on caoxial cable for long distance transmission.
CBX404
Impedance convertor AES (quad) - BNC75 Ohm -> XLR 110 Ohm
Impedance convertor AES (quad) - BNC75 Ohm -> XLR 110 Ohm
CBX404 is a quadruple impedance converter AES3id BNC (75 Ohms) to AES3 XLR (110 Ohms)
Application :
* Converter for audio digital format and impedance.
* Converter from balanced XLR format to BNC for long distance transmission.
CDM404
Broadcast modulation central 4 to 1
Broadcast modulation central 4 to 1
The CDM 404 is equiped with a stereo cue and monitoring section where the three input signals and the output can be mixed. This section includes a monitor output (line level), an headphone output and a bargraph which can be configured as a peakmeter or display RMS reading
CDM404_T
Remote control for CDM404
Remote control for CDM404
CDM 404 remote control interface with display
CNA300
A/D convertor, 24 bit, 21/44,1/48/96 kHz - balanced inputs
A/D convertor, 24 bit, 21/44,1/48/96 kHz - balanced inputs
Converter A/D - 24 bits - 32/44,1/48/96kHz -sym input.
CND400
D/A convertor, 24 bits, 32/44,1/48/96 kHz - balanced outputs
D/A convertor, 24 bits, 32/44,1/48/96 kHz - balanced outputs
Converter D/A - 24 bits - 32/44,1/48/96kHz - sym output.
CNF100
Dual sample frequency convertor AES/EBU - SPDIF
Dual sample frequency convertor AES/EBU - SPDIF
The CNF 100 is an universal sampling rate converter. The structure of the CNF 100 means that it can easily resolve all communication problems (and in both directions!) between two pieces of digital audio equipment working on different or non-synchronised sampling rates (example: a CD player and a professional digital audio studio working at 48 kHz). In fact, both the CNF 100 integrated converters pick up the synchronisation signal extracted from the opposite decoded digital source. All equipment connected to the appliance can, therefore, receive a digital audio signal synchronised with regard to it's own Output channel on the right frequency. A Word clock Clock signal is not necessary. The source sampling rate detection is automatic. The CNF 100 Input channel receives all professional and semi-professional AES/EBU, S/PDIF, IEC 958 digital audio standards.
COMPACT2_01
On-air/Production console, 5 mic, 15 line, 7 aux inputs, standard potentiometers
On-air/Production console, 5 mic, 15 line, 7 aux inputs, standard potentiometers
The COMPACT is a user-friendly console perfectly adapted to the field of radio broadcasting. Without taking up a great deal of space, the COMPACT has all the functions necessary to satisfy the most demanding of requirements whether it be in a studio, post-Oldproduction or even on-air.
COMPACT2_02
On-air/Production console, 5 mic, 15 line, 7 aux inputs, professional potentiometers
On-air/Production console, 5 mic, 15 line, 7 aux inputs, professional potentiometers
The COMPACT is a user-friendly console perfectly adapted to the field of radio broadcasting. Without taking up a great deal of space, the COMPACT has all the functions necessary to satisfy the most demanding of requirements whether it be in a studio, post-production or even on-air.
COMPACT2_03
On-air/Production console, 5 mic, 15 line, 7 aux inputs, cond plastic potentiometers
On-air/Production console, 5 mic, 15 line, 7 aux inputs, cond plastic potentiometers
The COMPACT is a user-friendly console perfectly adapted to the field of radio broadcasting. Without taking up a great deal of space, the COMPACT has all the functions necessary to satisfy the most demanding of requirements whether it be in a studio, post-production or even on-air.
CSS101
Digital audio signal missing detector
Digital audio signal missing detector
The CSS 101 is designed to continuously control a digital stereo audio signal. A problem on its main input will cause the automatic swing on a save digital signal. Of course, the CSS 101 swings back automatically on the main signal when all problems are resolved.
CSS203
Signal missing and out of phase detector
Signal missing and out of phase detector
The CSS 203 affords the control of the audio modulation presence. Inserted on a stereo audio link, it allows the monitoring of two unsimultaneous balanced stereo sources to one balanced stereo output. It comprises two sections: the first one controls the modulation presence, and the second controls the phase between the left channel and the right channel.
CXB404
Impedance convertor AES (quad) - XLR 110 Ohm ->BNC75 Ohm
Impedance convertor AES (quad) - XLR 110 Ohm ->BNC75 Ohm
CXB 404 is a quadruple impedance converter AES3 XLR (110 Ohms) to AES3id BNC (75 Ohms)
This device allows to link digital audio equipments using different formats. It also allows, when using limited distance AES3 XLR (110 ohms), to move too 75 ohms, the signal travelling on caoxial cable for long distance transmission.
EQA202
8 band corrector, SLIMRACK
8 band corrector, SLIMRACK
The EQA 202 is a stereo corrector of frequencies. It has: Symmetrical stereo Inputs / outputs on XLR. Asymmetrical stereo Inputs/outputs on cinch. One low-pass Filter (40 Hz) of type Butterworth (12 dB per octave). One high-pass Filter (12 Khz) of type Butterworth (12 dB per octave). One adjustment of the profit of exit (+/- 15 dB) at various frequencies: 63 Hz, 125 Hz, 250 Hz, 500 Hz, 1 Khz, 2Khz, 4 Khz and 8 Khz. One bypass mode of the equalizer.
EXT110
AES/EBU and SPDIF extension, 1 to 10 or 2 x 1 to 5, analogue PFL
AES/EBU and SPDIF extension, 1 to 10 or 2 x 1 to 5, analogue PFL
This dual distribution amplifier allows the number of digital Output channels of two pieces of equipment to be increased whilst maintaining the internal AES-3 (IEC 956) standards for each Output channel. The EXT 110 is transparent with regard to the transmitted digital data. The Input channel adapts to all sizes of professional and semi-professional, AES/EBU, S/PDIF, IEC 958, digital audio standards
EXT124
AES/EBU distribution, 1 to 4 or 2 x 1 to 2, SLIMRACK
AES/EBU distribution, 1 to 4 or 2 x 1 to 2, SLIMRACK
Distributor AES/EBU Distributor - 1 to 4 or 2 x 1 to 2 - Slimrack
EXT202_ET
RAM-00EXT202-000ET
RAM-00EXT202-000ET
The EXT 202 is a top range dual amplifier which allows the interfacing of two audio units with different working levels while keeping the signal quality very high.
EXT208S_EE
Broadcast line extension 1 to 4 stereo, I/O electronically balanced
Broadcast line extension 1 to 4 stereo, I/O electronically balanced
The EXT 206S and EXT 208S splitters have been designed to route the subsequent stereo programme input source to three or four stereo channels, keeping a very high signal quality. All outputs are implemented with individual amplifiers to prevant any interaction between the "Send signals".
EXT220/2_EE
Ip/Op board electronically balanced
Ip/Op board electronically balanced
EXT 220-2 is an audio signal distiributor. EXT220-2 is the perfect answer for audio signal dispatching in various domains, such as broadcasting, night clubs, sound systems. It allows to balance and transmit high level signals, avoiding local disturbances. EXT 220-2 is house in a 3U 19" case, the design is modular. Thanks to the LINK possibility, numerous configuration are allowed :
a) Option ten circuits and one power supply : for instance 1 stereo towards 10; two times 1 towards 5; 1to 4; 1to 6; or 10 to 1.
b) Option 8 circuits and 2 power supplies and supervisors : for instance 1 stereo towards 10; two times 1 towards 5; 1 to 4; 1 to 6; or 8 to 1.
EXT410
balanced distribution, 1 to 5 stereo
balanced distribution, 1 to 5 stereo
The EXT 410 is a top range splitter designed to route the subsequent stereo programme input source to five stereo channels keeping a very hight quality. All outputs are implemented with individual amplifiers to prevant any interaction between the send signal.
EXT832
Distribution 8 to 32 -RJ45
Distribution 8 to 32 -RJ45
Distributor 8 to 32 - RJ45
EXV121
Video distribution 12 sections
Video distribution 12 sections
Video distributor
FDI1000
Relais interface for remote control, pulse or cont - 10 sections (linkable)
Relais interface for remote control, pulse or cont - 10 sections (linkable)
Universal configurable independent 10-section start /stop
FDI300-2
Relais interface for remote control, pulse or cont - 3 sections start/stop
Relais interface for remote control, pulse or cont - 3 sections start/stop
FDI 300-2 is a magic box for switching signals modification such as logical level (or dry loop) to pulse or continuous dry loop or pulse l(ogical level or dry loop) to continuous dry loop.
FDI800
Relais interface - 8 sections - SLIMRACK
Relais interface - 8 sections - SLIMRACK
Universal start / stop - 8 sections - Slimrack
FRT100
Adaption for mounting SLIMRACK housing
Adaption for mounting SLIMRACK housing
1 SLIMRACK frame adapter for fitting
FRT200
19 inch 1U rack adaption for 2 SLIMRACK housings
19 inch 1U rack adaption for 2 SLIMRACK housings
19" 1U rack adapter for 2 SLIMRACK cases
FRT300
Blank plate for FRT200
Blank plate for FRT200
Blank SLIMRACK panel for FRT 200
GEM606
Grille 6x6 de reportage st
Grille 6x6 de reportage st
GEM 606 is a mixable designed to make the monitoring management easier during the radio program broadcasting specially outside. GEM 606 is developped to replace the whole equipment needed for the mixing, the routing, the order control and the headphone network management.
GEM 606, designed accordind to a "total recall" architecture, affords to assign 6 inputs to 6 headphone type stereo outputs. The user have 4 memories to save his configurations, and can recall them at any moment. A "mute" function allows to switch the matrix into the standy mode. (cut of all outputs)
GEM 606, designed accordind to a "total recall" architecture, affords to assign 6 inputs to 6 headphone type stereo outputs. The user have 4 memories to save his configurations, and can recall them at any moment. A "mute" function allows to switch the matrix into the standy mode. (cut of all outputs)
INT100
INT 104 in PCI version
INT 104 in PCI version
INT100 is a interface intended to perform the link between your computers system and your broadcast or production studio.
Using the computer USB port, it allows direct control of external sources (CD/MD players, mixing console, external remote controls)
Thanks to the dedicated software, the user keeps the full control of all external or embedded equipment, such as players, mixing console and so on.
INT100 is fitted with 3 inputs and 8 outputs in PC card format.
INT104
Universal interface for parrallel and serial port +USB
Universal interface for parrallel and serial port +USB
INT104 is a interface intended to perform the link between your computers system and your broadcast or production studio.
Using the computer serial, parallel oder USB port, it allows direct control of external sources (CD/MD players, mixing console, external remote controls)
Thanks to the dedicated software, the user keeps the full control of all external or embedded equipment, such as players, mixing console and so on.
* INT 104 is fitted with 8 inputs and 8 outputs in rack mount 19".
MIX802-2
4 stereo input mixer - VCA I/O option - VU - Headphones - monitor
4 stereo input mixer - VCA I/O option - VU - Headphones - monitor
Stereo Mixer - 6 mic/line - voice over - 2 stereo outputs - 4 mono
MIX802-2_SC2
Control surface for MIX808-2 + Mix802-2 VCA
Control surface for MIX808-2 + Mix802-2 VCA
MIX 802-2 SC2 desk, connected to MIX 802-2 VCA allows to mix 4 stereo signals or 8 balanced stéréo signals to a stereo balanced output.
MIX 802-2 can be rack mounted, and the control desk near the working station.
A heaphone output with volume control is available from the rear panel.
NRT305
DD0110-DD11S and GPI card with cables
DD0110-DD11S and GPI card with cables
NRT 305 interfaces input / output cards GPO - GPI with computers boards.
It delivers a 12V supply to feed the specific remote control. This voltage also supplies input optocouplers on input/output boards, allowing to use dry loop or open collector.
Two identical groups each with a 37 pins Sub D, dispatched on inputs/ouputs, sending inputs to a 25 pins female Sub D and outputs to a 25 pins male Sub D.
ODM300
remote transmitter surveillance, tuner + hybrid with automatic pick-up
remote transmitter surveillance, tuner + hybrid with automatic pick-up
The ODM 300 consists of a FM receiver tuner and a telephone hybrid for monitoring HF emmission via the telephone network.
PCS241
PSU 24V/1A - SLIMRACK
PSU 24V/1A - SLIMRACK
Power supply 24V/1A - Slimrack
PCS300
Headphone amps, desktop to build-in, external PSU PCS320
Headphone amps, desktop to build-in, external PSU PCS320
These small stereo amplifiers have a sophisticated Output channel element which works at low impedance and solves problems created by the low impedance headphones.
PCS320
External PSU - 18VDC/16W
External PSU - 18VDC/16W
External power supply - 18VCC / 16W.
PMI101 Pack 01
Microphone preamp to integrate + pcs320
Microphone preamp to integrate + pcs320
Its transistor input provides an EIN noise rate of 130 dB (A-weighted). The Line output can be balanced or unbalanced. The level is controlled using a screwdriver and it is simplified with the help of an ON / PEAK LED which goes out when it levels out. A push button momentarily mutes the Output channel.
PMI304
Preamp/mixer 3 mics, 48V, direct line outputs + mix
Preamp/mixer 3 mics, 48V, direct line outputs + mix
The PMI 304 is a compact unit from the Slimrack range which allows the pre-amplification and mixing of 3 balanced microphones as well as an unbalanced Line Input channel.
PMI603
Stereo mixer 6 mic/line - voice over - optional VCA on outputs
Stereo mixer 6 mic/line - voice over - optional VCA on outputs
In addition to its multiple source connection feature (up to 13 sources spread out over 7 Input channels), the optional VCA 100 is available which means the PMI 603 Output channel levels can be controlled by remote control with the possibility of disabling the potentiometers on the front of the equipment. (Attention 2xVCA100 are required for one stereo channel).
PMI604S
Stereo mixer 6 mic/line - priority - noise gate - limiter
Stereo mixer 6 mic/line - priority - noise gate - limiter
The PMI 604S is a stereophonic mixer with micro preamplifiers. It has the following characteristics: Bass / Treble can be adjust per input to optimize each source sound. The balanced micro input and the peakmeter sensibility can be adjust per input, allowing to fit all types of microphone. The integrated phantom power supply allows the connexion of static microphones. The compressor / autofader of the micro input 1 allows the flow of priority announcements or messages on other sources. The adjustable noise gate allows to free from ambiant noise. The configuration of inputs in master or slave, allows to configurate a downward priority from input 1 to input 6. The limiter on main output guarantee an optimum working in function with various users. The PMI 604S is used for critical applications because of it's very low noise level on the micro inputs.
PMI8080
Chassis bac Europe pour carte pr
Chassis bac Europe pour carte pr
PMI 808 features 8 microphone preamp boards with line level balanced output. PMI808 can be fitted with less than 8 boards. Input circuit has an excellent S/N figure, that compares favorably with studio console inputs.
A switchable phantom power supply allows use of electrostatics microphones. Input level ranges from -60dBu to -26dBu, a peakmeter shows saturation. A switchable two bands tone corrector, allows sound color ajustement, according to particular needs. A switchable low frequequency cut filter, cancels unwanted « pops ». Opening the microphone can be remotely achieved, using a continuous loop or a start/stop pulse.
A GPO output is avalable to confirm the microphone opening using either a loop or a voltage (Switch on, opening warning light).
The frame comes with two power supplies, one for normal use, one as a spare. Switching between power supplies is manual or automatic. A special circuit, monitors the quality of supply and manage the switching in case of malfunction of the power supply or mains.
A switchable phantom power supply allows use of electrostatics microphones. Input level ranges from -60dBu to -26dBu, a peakmeter shows saturation. A switchable two bands tone corrector, allows sound color ajustement, according to particular needs. A switchable low frequequency cut filter, cancels unwanted « pops ». Opening the microphone can be remotely achieved, using a continuous loop or a start/stop pulse.
A GPO output is avalable to confirm the microphone opening using either a loop or a voltage (Switch on, opening warning light).
The frame comes with two power supplies, one for normal use, one as a spare. Switching between power supplies is manual or automatic. A special circuit, monitors the quality of supply and manage the switching in case of malfunction of the power supply or mains.
PORTA_REPORT
Portable telephone insert GSM/RTC - 2 mics - 2 Headphones
Portable telephone insert GSM/RTC - 2 mics - 2 Headphones
Porta Report is designed for live outside broadcast capable of using analogue (Commutated Telephone Network) or Wireless(GSM).
PRF101
Speaker Console LR
Speaker Console LR
PRF 101 allows remote control in broadcasting applications.
It is specially designed to be used with ART 864.
It is specially designed to be used with ART 864.
* 12 push buttons with integrated warning light.
* 12 warning light returns.
* 2 control potentiometers.
* 1 ON AIR warning light.
* 2 headphone output.
* Connection using Sud D 25 wire and connectors.
PRC100
Pupitre Chef d'orchestre
Pupitre Chef d'orchestre
PRC100 is a 4 wires interface for telephone handset. Inputs and returns use balanced XLR. A warning light shows detected incomming order. PRC100 allows connection of ordinary net, to environments like editing room, or orchestra training.
PRF10A
Wiring interface for PRF101
Wiring interface for PRF101
PRF10A is a « Slimrack » case, to make PRF101 and PRF 55 wiring, easy.
PRF44
Console 4 sends/indicators LR
Console 4 sends/indicators LR
PRF44 allows remote control in broadcasting applications.
It is specially designed to be used with ART864.
It is specially designed to be used with ART864.
* 4 push buttons with integrated warning light.
* 4 warning light returns.
* Connection using Sud D 25 wire and connectors
PRF60_E2
Pupitre encastrable 2 switchs/voyants + casque actif + on air
Pupitre encastrable 2 switchs/voyants + casque actif + on air
PRF60 a desktop or slot in case, features an headphones amplifier, switches for remote control, and one ON AIR light. PRF 60 is avalaible with different options
PRF55
Console speaker LR
Console speaker LR
PRF55 allows remote control in broadcasting applications.
It is specially designed to be used with ART864.
It is specially designed to be used with ART864.
* 4 push buttons with integrated warning light.
* 4 warning light returns.
* 2 control potentiometers.
* 1 ON AIR warning light.
* 1 headphone output.
* Connection using Sud D 25 wire and connectors.
PRF60_B2
Pupitre de table 2 switchs/voyants + casque actif + onair
Pupitre de table 2 switchs/voyants + casque actif + onair
PRF60 a desktop or slot in case, features an headphones amplifier, switches for remote control, and one ON AIR light. PRF 60 is avalaible with different options
PRS100
Pupitre ordre 4 fils - D
Pupitre ordre 4 fils - D
PRS100 is an order desk with 4 wires. It allows :
* To receive orders on a loudspeaker or headphone (pluging headphone, cut off the loudspeaker). Amplifier and loudspeaker are powerfull enough to allow perfect intelligibility. It is also possible to use an external loudspeaker. Transformer balanced input on XLR. A warning shows detected in comming order.
* To send orders from the microphone (front panel XLR with phantom supply) to a transformer balanced output on XLR. The microphone level is adjustable (peak led) and a limter avoids any input saturation. An adjustable dimmer reduces the loudspeaker output, when sending order. A switch at the rear copy input to output thus allowing to chain several PRS100. Unit can be powered from the mains or a 12V battery.
Some other talk back desks are available , referenced PRS 200, PRC 100.
PRT505
Headphone amp - command return - on/off - command to console
Headphone amp - command return - on/off - command to console
Start / Stop console managment with ON / OFF lights for TALLY return. One switch to manage order network. One Headphone amplifier with audio inputs on symetrical line. Headphone jack in rear or front panel to carry out connector on the office. One console return order sent in animator headphone. The order modulation can be sent to left or / and right animator ears. A dimming is inserted or main program when order is activated. One AUX connector to take up the console modulation, the order modulation and the order loop to feed a second PRT 505 or PCS300. One integrate limitor designed to avoid extreme level on headphones.
PRS200
Pupitre 4 fils - Retour St
Pupitre 4 fils - Retour St
PRS200 provides automation systems, and a mute input when "ON AIR" the same features as PRS100 but is more dedicated to radio studios. It does provide a loop output for automation systems, and a mute input when "ON AIR"
PRT666 Pack 01
DJ console, 1 mic send, 2 commands - headphones - RED light - Phantom power
DJ console, 1 mic send, 2 commands - headphones - RED light - Phantom power
PRT 666 is a multifunction desk, answering to mobile or fixed various needs.
PRT700
Command console
Command console
OUTPUT : *Order with hight dynamic microphone. *Limitor on Microphone guarantee an optimum function in case of different users. *Level controlled using a screwdriver for order Mic. *One Mic order balanced without selection. Eight Mic order balanced with selection and external status.
PRT750
Command console - 19 inch 1U
Command console - 19 inch 1U
OUTPUT : *Order with hight dynamic microphone. *Limitor on Microphone guarantee an optimum function in case of different users. *Level controlled using a screwdriver for order Mic. *One Mic order balanced without selection. Eight Mic order balanced with selection and external status.
PRT800
Boitier d'ordre 1U - 8 Zones
Boitier d'ordre 1U - 8 Zones
PRT 800 is an eight channel intercom. Its 1 unit 19 pouces cabinet, eases the fitting in report vehicles and mobile control rooms. An auxiliary return, automaticaly fades on talk back input, allowing the local program or antenna return monitoring.
RCA627
Encoder top 27Hz
Encoder top 27Hz
The RCA 627 allows a subsonic pulse to be mixed with a monophonic or stereophonic modulation. That way, devices can be remotely activated by this pulse using the same transmission line as the audio modulation. The classic installation block diagram is composed with the RCA 627 at one end of the transmission (local studio) and at the other end (emittor local), a decoding machine.
RGL260
RED/GREEN signalisation 24V - multileds 20 - internal or external
RED/GREEN signalisation 24V - multileds 20 - internal or external
PERIPHERICAL INTERFACES Visual Led red/green (24V)
RGL500
LED 'ON AIR' panel, 24VDC
LED 'ON AIR' panel, 24VDC
PERIPHERICAL INTERFACES Visual Led red "ON AIR" (24V)
RMT2066
Phase correlato', assignable inchANT inch or inchCUE inch or inchPCM2 inch or inchTUNER inch
Phase correlato', assignable inchANT inch or inchCUE inch or inchPCM2 inch or inchTUNER inch
SEL104-2
Selector 1 out of 10 balanced stereo inputs - remote control via TLC100
Selector 1 out of 10 balanced stereo inputs - remote control via TLC100
SEL104 / SEL110 remote control.
SEL110-2
AES/EBU or SPDIF 1 out of 10 selector, analogue PFL, remote controllable
AES/EBU or SPDIF 1 out of 10 selector, analogue PFL, remote controllable
This selector routes one of the ten digital audio Input signals, firstly, to a digital audio Output that conforms with the specifications contained in the international AES-3 (IEC 958) standards and, secondly, to a balanced analogue audio Output using its top quality D/A 20 bit converter.
SEL114
AES/EBU selector - 1 out of 4 - Slimrack
AES/EBU selector - 1 out of 4 - Slimrack
The SEL 114 is a Slimrack standard selector allowing to route one digital audio input, among four, to one same standard output. The whole selection is made according to a synchronus commutation method: the SEL 114 commute to the new selected source when the last frame is finished.
SEV101
Video Composite selector 10 inputs, 2 outputs, preview, remote controllable.
Video Composite selector 10 inputs, 2 outputs, preview, remote controllable.
Video selector 10 inputs - 2 outputs - préview - Remote control.
SYM424
Passive 2 channel translator - 1/2 rack (optional FRT200 and FRT300)
Passive 2 channel translator - 1/2 rack (optional FRT200 and FRT300)
The SYM 424S has been designed to balance two line links. The transformer's bandwidth is wider than that used in audio.
TEL1052
Telephone central 5 lines with control of 2 external inserts
Telephone central 5 lines with control of 2 external inserts
5 Telecom lines router with remote control.
TEL150
Telephone insert
Telephone insert
The TEL 150 is a telephone hybrid designed to be adapted to any console as a result of its multi-function flowchart for organising debates, conferences, games or just speeches made by members of the audience
TEL300S
Telephone insert, automatic pickup, input mic/line, headphones, remote controllable
Telephone insert, automatic pickup, input mic/line, headphones, remote controllable
The TEL 300 can be adapted to any type of console equipped with a specific channel (N - 1) , such as COMPACT or RP 2000. The use of an auxillary send can be an alternative for consoles that do not have a specific channel
TEL300_EE
Telephone insert remote controllable, I/O balanced
Telephone insert remote controllable, I/O balanced
TEL300 can be adapted to any type of console equipped with a specific channel (N - 1), such as COMPACT or RP2000. The use of an auxillary send can be an alternative for consoles that do not have a specific channel.
TEL400
Dual telephone insert , 2 lines, remote controllable
Dual telephone insert , 2 lines, remote controllable
Double hybrid with telecom line switcher.
TLC800
T
T
TLC 800 is a remote control featuring 8 fugitive keys with lights. This remote control is an all pupose device :
* The keys deliver individually a dry loop or a voltage, according to the internal setting (the voltage will be from external source)
* The lights are switched on either an external voltage, or a dry loop, open collector or drain.
SLIMRACK accessories :
FRT 100 : Front panel adapter for fitting one "Slimrack".
FRT 200 : Rack 19"1U front panel adapter for 2 "Slimrack" units.
FRT 300 : cover plate for FRT200.
TLC100
Remote control for SEL104/SEL110
Remote control for SEL104/SEL110
SEL104 / SEL110 remote control.
TSM300
Voice sound processing
Voice sound processing
The TSM 300 is a total microphone sound processecor developed for a Broadcast utilisation (radio, television...). It's equipped with the complete collection of audio processing needed for a micro processing. All parameters can be saved, after modifications, which permit an easier recall. Each animator or journalist can quickly have direct access to an individual and personalized configuration establiched according to his vocals characteristics.
TUS202
Line amplifier balancer, transfo outputs, adjustable gain, 1/2 rack
Line amplifier balancer, transfo outputs, adjustable gain, 1/2 rack
This top quality dual amplifier adapts an unbalanced or balanced source to a balanced output with transformers. The gain adjust, the output channel low impedance, and the output channel high level allow the TUS 202 to be integrated into a professional installation
TUS203
Mondo reducer balanced line amplifier
Mondo reducer balanced line amplifier
This top quality dual amplifier adapts an unbalanced or balanced source to two mono balanced outputs with transformers.
TUS404
Dual translator stereo unbalanced/balanced - balanced/unbalanced, SLIMRACK
Dual translator stereo unbalanced/balanced - balanced/unbalanced, SLIMRACK
The TUS 404 has two distinct sections A and B : A : Two right and left channels affords to transform an unbalanced modulation to a balanced modulation. The gain is adjustable from 0dB to +22dB. (independent right and left controls). B : Two right and left channels affords to transform a balanced modulation to an unbalanced modulation. The gain is adjustable from -22dB to 0dB. (independent right and left controls).
TUS408
4 channel balancer RCA to XLR
4 channel balancer RCA to XLR
The TUS 408 affords to transform four unbalanced modulations to four balanced modulations with their own level and impedance adapt. Each channel has a gain control from 0 to 22dB.
VCA100
VCA board for RAMI and AMIX equipment
VCA board for RAMI and AMIX equipment
Optionnal VCA card for Rami and AMIX equipment.
VCA500
Controleur de gain 1 canal num
Controleur de gain 1 canal num
VCA 500 allows to control the digital audio signal level. It is made of two main sections:
* One fixed gain stage (+/- 12 dB)
* One adjustable gain stage, remotely controled using a normal potentiometer.
* One peakmeter displaying the digital audio signal filling, allows accurate gain setting.
* XLR digital input and transformer (AES/EBU)
* XLR digital output and transformer (AES/EBU)
* Manage all digital audio signals formats
* Digital source errors indicator.
SLIMRACK accessories :
* FRT 100: Front panel adapter for fitting one "SLIMRACK."
* FRT 200: Rack 19" 1U front panel adapter for 2 "SLIMRACK" units.
* FRT 300: Cover plate for FRT 200.
VCA200
2 channel balanced VCA, adjustable or calibrated gain, SLIMRACK
2 channel balanced VCA, adjustable or calibrated gain, SLIMRACK
The VCA 200, when inserted in an amplification system, allows sound volume to be remote controlled.
VGA404
Video Matrix - VGA/component/composite/Y/C
Video Matrix - VGA/component/composite/Y/C
The VGA 404 is a 4x4 video matrix. It was designed to assign a VGA video source (among 4) to one of the four available outputs : Only one output can be associated to one input. The same input can be routed on severals outputs.